Recherche Menu Cachés

Posez ici tous vos problèmes électriques ainsi que tout ce qui est lié aux alarmes, ODB, DME, etc.
Répondre
Kristov
Messages : 480
Inscription : lun. août 08, 2005 7:35 am
Localisation : 78180

Recherche Menu Cachés

Message par Kristov »

Bonjour à tous,

Je recherche les menus cachés sur mon ordinateur de bord ou/et sur mon tableau de bord.

J'ai un ODB comme celui ci:

Image

Ma voiture: E34 1991 525i24S M50


Merci
@+ :surprise:

Avatar de l’utilisateur
JWEST
Messages : 1408
Inscription : ven. oct. 11, 2002 1:01 pm
Localisation : ESSONNE

Re: Recherche Menu Cachés

Message par JWEST »

Salut,

Il n'y a rien de caché sur ce boitié qui n'est en fait qu'une grosse horloge donnant la date et la température extérieure (sans parler du dong toutes les heures).

Ce n'est pas un ODB ;)
E39 Image boite 6

Avatar de l’utilisateur
dehel
Messages : 32
Inscription : mer. nov. 23, 2005 10:03 am
Localisation : Vif (15km de Grenoble)

Re: Recherche Menu Cachés

Message par dehel »

Salut,

J'ai la même voiture java script:emoticon(':surprise:')
smilie, et effectivement ce n'est pas un ODB. Par contre, je crois que le cablage derrière est présent, donc modulo l'achat d'un ODB d'occas, il est peut-être possible d'en mettre un quand même. Il me semble avoir vu la procedure en photo sur un site (mais je ne sais plus lequel java script:emoticon(':(')
smilie), mais il faut faire très attention car il y a une histoire de versions d'ODB et de compatibilité...

A+
Didier
M5 Evolution
ex525i-1991

Kristov
Messages : 480
Inscription : lun. août 08, 2005 7:35 am
Localisation : 78180

Re: Recherche Menu Cachés

Message par Kristov »

Bonjour,

et avec mes deux boutons de mon tableau de bord!???

Je peux faire quelquechose... j'ai réussi à changer de langue..

:D

Mais y a pas autre chose?

Avatar de l’utilisateur
dan_lau
Messages : 511
Inscription : mar. sept. 23, 2003 8:51 pm
Localisation : Rueil-Malmaison

Re: Recherche Menu Cachés

Message par dan_lau »

Si je puis me permettre, qu'est ce que tu cherches à faire ?
tu cherches quoi comme menu ?

y a bien un test du tableau de bord, qui consiste à appuyer sur le bouton du tableau de bord, puis de tourner la clé que contact au premier crant...
mais bon, je suis pas sur que ce soit bien ça que tu cherches !

Kristov
Messages : 480
Inscription : lun. août 08, 2005 7:35 am
Localisation : 78180

Re: Recherche Menu Cachés

Message par Kristov »

C'est parceque j'avais trouvé ça comme info:
Sur le site www.bmwe34.net

"The first thing to do when you troubleshoot your Bmw E34 engine is to read your Engine Codes. (not all codes apply to all engines)

1211 DME Control Unit
1215 Air Mass Sensor
1216 Throttle Potentiometer
1218 Output Stage, Group 1
1219 Output Stage, Group 2
1221 Oxygen Sensor 1
1212 Oxygen Sensor 2
1222 Lambda Control 1
1213 Lambda Control 2
1223 Coolant Temperature Sensor
1224 Intake Air Temperature Sensor
1225 Knock Sensor 1
1226 Knock Sensor 2
1227 Knock Sensor 3
1228 Knock Sensor 4
1231 Battery Voltage/DME Main Relay
1232 Throttle Idle Switch
1233 Throttle Wide Open Throttle Switch
1234 Speedometer A Signal
1237 A/C Compressor Cut Off
1242 A/C Compressor
1243 Crankshaft Pulse Sensor
1244 Camshaft Sensor
1245 Intervention AEGS
1247 Ignition Secondary Monitor
1251 Fuel Injector 1 (or group 1)
1252 Fuel Injector 2 (or group 2)
1253 Fuel Injector 3
1254 Fuel Injector 4
1255 Fuel Injector 5
1256 Fuel Injector 6
1257 Fuel Injector 7
1258 Fuel Injector 8
1261 Fuel Pump Relay Control
1262 Idle Speed Actuator
1263 Purge Valve
1264 EGO Heater
1265 Fault Lamp (check engine light)
1266 VANOS
1267 Air Pump Relay Control
1271 Ignition Coil 1
1272 Ignition Coil 2
1273 Ignition Coil 3
1274 Ignition Coil 4
1275 Ignition Coil 5
1276 Ignition Coil 6
1277 Ignition Coil 7
1278 Ignition Coil 8
1281 Control Unit Memory Supply
1282 Fault Code Memory
1283 Fuel Injector Output Stage
1286 Knock Control Test Pulse
1444 No Fault Codes

If you cannot read them that means that you have a bad bulb or no buld at all. Older E34's don't have a check engine bulb wired.

1. Turn the ignition key on (without starting the car) and depress the accelerator pedal to the floor 5 times within 5 seconds.
2. The check engine light will remain lit for 5 seconds, blink off, light for 2.5 seconds, goes off for 2.5 sec. and will start flashing the codes.
3. Each code is separated by a 2.5 sec. pause. A 0.5 sec. blink then nothing means the end of the code reading. To read them again, depress the accelerator pedal 5 times again.

Clear the codes
1. Read the codes. At the end, make sure that the 1000 code (short blink and nothing) is present then depress the accelerator for at least 10 seconds.
2. To check, depress the accelerator pedal 5 times within 5 sec and make sure that the 1444 code (no fault stored) is present.

Car code display
With the key off, press in the OBC display reset button on the dash below the tach (the one that makes your readout disappear). Hold it in for 3 seconds and turn the key to position 2. Release the button, watch all of the car codings and then the final light show. That is the only way I want to see the tach go that high."

Et je voulais savoir si cela marche sur ma voiture....J'ai essayé mais sans succés.


Voilà c'est tout! :wacko:

Avatar de l’utilisateur
fred_rennes
Messages : 1982
Inscription : lun. janv. 06, 2003 3:41 pm
Localisation : Lausanne

Re: Recherche Menu Cachés

Message par fred_rennes »

Kristov a écrit :If you cannot read them that means that you have a bad bulb or no buld at all. Older E34's don't have a check engine bulb wired.


Et je voulais savoir si cela marche sur ma voiture....J'ai essayé mais sans succés.
Ta voiture n'est pas équipée du module check.....
Lausanne - CH
ex : 206 SW HDi 2.0l / 520i e34 m20 / 316i e36 compact / 318i e36
325i cab e36, en BZH pour les vacances
X5 4.4i v8 "pousse toi"
Image

Kristov
Messages : 480
Inscription : lun. août 08, 2005 7:35 am
Localisation : 78180

Re: Recherche Menu Cachés

Message par Kristov »

Ma voiture est une 525i M50 24S de 1991.

Et je suis sûre que sur mon CHECK CONTROL, une fois j'ai réussi a avoir la version de mon check control.

Mais surtout je voudrais savoir si je peux avoir les codes erreurs .

Merci à tous.

:D

Répondre

Revenir à « Electricité - Alarmes - ODB - DME - Clim »

Qui est en ligne ?

Utilisateurs parcourant ce forum : Aucun utilisateur inscrit et 15 invités